Nominal load at COG: 1.8t – Standard tyres: 2x/2SE/V/P – Total width: 1080mm – Construction height: 1980mm – Centre of gravity: 50…
Nominal load at COG: 1.8t – Standard tyres: 2x/2SE/V/P – Total width: 1080mm – Construction height: 1980mm – Centre of gravity: 500mm – Drive system: D
Crown is the manufacturer of the SC 4240 1,8 electric forklift. The production years for this model are (2008 - 2012). Find here detailed specs for SC 4240 1,8 electric powered lift truck - in a form of table chart below and downloadable datasheet. Explore also the other forklift models produced by Crown.
All specifications and prices refer to basic models with standard fork carrier, 2 standard prongs without additional hydraulics, battery, charger. With Simplex mast (3,3m up to 10t • 5m > 10t load capacity). L = pneumatic tyres, x = drive, SE = superelastic, P = PUR (Elastollan, Vulkollan), V = solid rubber, ND = low-pressure tyres, 3 = three-wheel, 4 = four-wheel, 6 = six-wheel
Variable regenerative motor braking is optimised and assisted with electric friction brakes, eliminating maintenance associated with typical wet, disk or drum style brakes. The appropriate amount of stopping force is applied to match operator brake input and the current operating conditions of the truck. The closed loop Access 1 2 3 traction control will automatically keep the truck on hold until a travel input is requested, even when operating on a ramp. Automatic electric parking brakes activate when the operator leaves the seat, a travel input has not been requested or battery power has been disconnected.
Proportional Rack and Pinion Steering System
On-demand power steering is served by the main hydraulic pump when steering is requested. The hydrostatic power steering uses a large, totally enclosed rack and pinion gear assembly. The steering geometry is matched to the controller to deliver smooth steering at all angles. The advantage is less tyre scrubbing which extends tyre life. Both motors receive power, even in the tightest turns. This helps the truck to accelerate, turn and manoeuvre even from a full turn start position. Cornering speed control regulates the drive motor’s output by the turning degree of the truck. The advantage is smooth, stable steering which may increase operator confidence and productivity. Large, 380 mm diameter dual steer wheels provide good traction and stability and support straight travel over long distances.
Performance
Crown Drive System
Crown has applied the latest generation AC drive system, enhanced with Access 1 2 3 technology. The demand for high efficiency systems that closely match customer torque requirements is met with this latest generation control system. Crown-manufactured, independently controlled, AC drive motors are specifically designed to optimise system integration between the traction and braking controls. Crown’s Access 1 2 3 technology provides optimum performance and control by offering a communication interface for operators and technicians, intelligent coordination of lift truck system and simplified service with advanced diagnostics. The Crown display is used for easy troubleshooting, access service history and set performance features. Three modes of performance can be selected to accommodate operator experience or application requirements.
Hydraulics
Low noise hydraulic pump serves both lift and steer systems. The hydraulic system provides continuous filtration through suction filter and easy to service return filter. Hydraulic valve actuation is precise and oil is controlled using metered spool valves. 3 spool valve for lift/lower, tilt and an auxiliary function is standard and features an integrated pressure relief valve for system protection. A pressure compensation lowering valve ensures safe controlled lowering speeds. Ram displacement type lift cylinders and two double acting tilt cylinders are Crown-manufactured and designed for long life. All rams and piston rods are hard chrome plated to reduce pitting corrosion and extend cylinder packing life. O-ring face seal fittings are used to eliminate leaks.
Buy & Rent
Used Crown Electric forklifts for sale
LECTURA analyzes current offers from many sources about Electric forklifts. Find the selection of the best offers on often visited marketplaces presenting second hand Electric forklifts for sale in many countries.
Get in touch for more details:
Compare Crown SC 4240 1,8 with similar Electric forklifts
Electric forklifts appraisal with LECTURA Valuation
Whether you need to get value of your Crown SC 4240 1,8 or valuation of your Electric forklifts fleet, LECTURA Valuation will help. Simply fill the form and see the pricing information for Electric forklifts in few clicks.
Get spare parts for Crown SC 4240 1,8 easily from our partners
Do your lookup for high quality parts for Crown SC 4240 1,8 online!
With a few, easy steps, you will find generic and genuine parts and replacements in well-catalogued lists. Wether you are dealer or an owner, LECTURA can lead you to the right direction.
Check the best offers from our partners and order the Electric forklifts spare parts easily today - worldwide.
In case you look into transport options for your machine, apply our services. Examine the best fitting transport quotes for Electric forklifts created on transport dimensions and weights. Our partners provide large-scale options to satisfy your requirements.
Manitou Deutschland GmbH celebrated 30 years of success with machine demonstrations, a live band, a public viewing event, and, as a highlight, the unveiling of the strictly limited special edition MLT 742-140 V+.
.jpg)